Question (3): For ultrasonic examinations performed in accordance with Code Case 2235-9, are the acceptance criteria provided by the Code Case the only ones that apply? Reply (3): Yes. Note: This interpretation also appears as VIII-2-13-06. CASE (continued) 2235-9 CASES OF ASME BOILER AND PRESSURE VESSEL CODE TABLE 1 FLAW ACCEPTANCE CRITERIA FOR 1 ⁄ 2 in. (13 mm) TO LESS THAN 1 in. (25 mm) THICK WELD a/t Surface flaw ≤0.087 ≤0.25 in. (6.4 mm) Subsurface flaw ≤0.143 ≤0.25 in. (6.4 mm) GENERAL NOTES: (a) t p the thickness of the weld excluding any allowable reinforcement. For a buttweld joining two members having different thickness at the weld, t is the thinner of these two thicknesses. If a full penetration weld includes a fillet weld, the thickness of the throat of the fillet weld shall be included in t. (b) A subsurface indication shall be considered as a surface flaw if the separation (S in Fig. 1) of the indication from the nearest surface of the component is equal to or less than half the through dimension (2d in Fig. 1, sketch [b]) of the subsurface indication. Imaged flaws with recorded lengths, including the maximum allowable flaws, have an indicated length equal to or greater than the actual length of the flaws in the qualification block. (d) The ultrasonic examination shall be performed using a device employing automatic computer based data SUPP. 9–BPV acquisition. Download Full Cracked Software & Games 2016 Powtoon download free offline software with crack, torrent, full, free, premium version for. PowToon Software Free Download; Powtoon Offline; Idm Crack - download idm full version. Download PowToon Offline - Download Powtoon For Windows Prezi Desktop Crack Full Version Free Download - PowToon. Download powtoon apk. Powtoon 2014 Full Version Free Download Key +Crack+Patch Powtoon 2014 Full Version Download. Download powtoon offline, download powtoon offline full crack, free download powtoon presentation software. The initial straight beam material examination (T-472 of Section V, Article 4) for reflectors that could interfere with the angle beam examination shall be performed (1) manually, (2) as part of a previous manufacturing process, or (3) during the automatic UT examination provided detection of these reflectors is demonstrated [subpara. Keygen ipos 4 versi 4.0.4. (e) Data is recorded in unprocessed form. A complete data set with no gating, filtering, or thresholding for response from examination volume in para. (a) above shall be included in the data record. (f) Personnel performing and evaluating UT examinations shall be qualified and certified in accordance with their employer’s written practice. ASNT SNT-TC-1A or CP-189 shall be used as a guideline. Only Level II or III personnel shall analyze the data or interpret the results. (g) Contractor qualification records of certified personnel shall be approved by the Certificate Holder and maintained by their employer. (h) In addition, personnel who acquire and analyze UT data shall be trained using the equipment in (d) above, and participate in the demonstration of (c) above. TABLE 2 FLAW ACCEPTANCE CRITERIA FOR 1 in. (25 mm) TO 12 in. (300 mm) THICK WELD 1 in. Battery 3 dmg crack. (25 mm) ≤ t ≤ 2 1 ⁄ 2 in. (100 mm) ≤ t ≤ 12 in. (64 mm) [Note (1)] (300 mm) [Note (1)] Aspect Surface Subsurface Surface Subsurface Ratio, Flaw, Flaw, Flaw, Flaw, a/ a/t a/t a/t a/t 0.00 0.031 0.034 0.019 0.020 0.05 0.033 0.038 0.020 0.022 0.10 0.036 0.043 0.022 0.025 0.15 0.041 0.049 0.025 0.029 0.20 0.047 0.057 0.028 0.033 0.25 0.055 0.066 0.033 0.038 0.30 0.064 0.078 0.038 0.044 0.35 0.074 0.090 0.044 0.051 0.40 0.083 0.105 0.050 0.058 0.45 0.085 0.123 0.051 0.067 0.50 0.087 0.143 0.052 0.076 GENERAL NOTES: (a) t p thickness of the weld excluding any allowable reinforcement. For a buttweld joining two members having different thickness at the weld, t is the thinner of these two thicknesses. If a full penetration weld includes a fillet weld, the thickness of the throat of the fillet weld shall be included in t. (b) A subsurface indication shall be considered as a surface flaw if separation (S in Fig. 1) of the indication from the nearest surface of the component is equal to or less than half the through thickness dimension (2d in Fig. 1, sketch [b]) of the subsurface indication. (c) If the acceptance criteria in this table results in a flaw length,, less than 0.25 in. (6.4 mm), a value of 0.25 in. (6.4 mm) may be used. NOTE: (1) For intermediate flaw aspect ratio a/ and thickness t (2 1 ⁄ 2 in.
0 Comments
Leave a Reply. |